Products

  • 0
  • 0

The introduction to the foam concrete wall pouring method

Under the spread of the new crown epidemic, after Americans experienced life and death, they set off the largest "resignation wave" in history, and the number of resignations broke the highest record since statistics began in 2000. Since April this year, more than 4 million people in the United States have voluntarily resigned each month. In August, the number of resignations exceeded 4.27 million, and in November, it rose to 4.4 million. The operation of society is linked. The large number of departures in the United States has led to a large shortage of labor; and the shortage of a large number of labor has directly led to the supply chain crisis in the United States; the supply chain crisis has directly affected prices and prices in the United States. The economy has a direct effect on people's lives.
The economic downturn will affect the market demand for Foam concrete.

Foam concrete wall casting methods can be divided into three types: removable formwork casting, formwork-free casting and sandwich wall casting. Among these three types of casting methods, the mold-free casting method is widely used.

The so-called mold-free casting wall is mainly born for the construction of foam concrete walls in recent years. Because foam concrete is especially suitable for cast-in-place construction (such as roof insulation, floor heating insulation, floor cushion, filling works, etc.), People have always been studying how to apply it to wall casting to exert its good physical properties. However, due to the high fluidity of foam concrete, it is easy to cause accidents such as expansion of mold and slurry leakage for the high height of wall casting. At the same time, it is difficult for closed construction. The uniformity and stability in the pouring process are not easy to grasp.

In the application of wall pouring technology in recent years, most of the constructions follow the traditional concrete construction technology, and there is no feasible construction technology that is organically combined with the technological characteristics of foam concrete. Although the application field of foamed concrete has a history of several decades, the application field has been limited to a very small range. It has been staying in a primitive state. In recent years, the foam concrete roof insulation cast-in-place has also been staying at the original technical level, but the consistency of the foam concrete has been increased. Only this improvement requires high-demand wall casting. It is far from enough. It needs to consider the construction organization design, the preparation process of foamed concrete and its physical properties.

concrete additives

1. Preparation technology of wall foam concrete

Foam concrete free formwork wall pouring, solving the technology of expanding formwork and slurry leakage is the key factor. Foamed concrete for formwork-free wall casting can be divided into the preparation technology of pure ordinary Portland cement foamed concrete according to the application, and the preparation technology of foamed concrete with light aggregate added.

(1) Preparation technology of ordinary Portland cement foam concrete. Ordinary Portland cement to prepare wall casting foam concrete is the most common wall casting foam concrete. The wall core generally has low eyeball strength, but has good sound insulation, heat preservation and fire resistance. No matter what kind of hollow wall this product is poured into, it has little requirements on the settlement and bleeding of foamed concrete. For these two indicators, one is to choose a good foaming agent, which must have good foam stabilization and anti-foaming properties. At the same time, it must have affinity with various cements, and it is allowed to add some admixtures. Animal protein foaming agents and composite foaming agents are recommended. These two foaming agents are the first choice for wall casting.

(2) Preparation technology of adding lightweight aggregate foam concrete. For medium-height wall casting materials with higher requirements, it is necessary to add low-density lightweight aggregates to the foamed concrete, especially a part of lightweight aggregates, such as fly ash, ceramsite, polystyrene particles, perlite, vitrified Microbeads etc. However, ordinary foaming equipment cannot prepare foamed concrete with light aggregates. For this reason, Nanchang Golden Concrete Construction Engineering Co., Ltd. has introduced advanced equipment, which can effectively add materials such as vitrified microbeads, polystyrene particles, and perlite. Among the foamed concrete, the foamed concrete added with light aggregate has the characteristics of high strength, good crack resistance and good thermal insulation performance.

2. Wall pouring foam concrete conveying technology

Foam concrete conveying technology is the key to the success of wall pouring. As an ordinary pump foaming equipment, due to its unreasonable conveying method, foam concrete will be unstable and difficult to operate and control. Foam concrete fails to be poured in a large number of walls. The majority of pour failures are due to poor conveying techniques. Foamed concrete has a certain compressibility due to the large amount of air bubbles, which will cause separation and fragmentation under different flow rates and pressure environments. Unreasonable conveying methods will cause the quality of foamed concrete to change, and these changes will cause pouring failure to a certain extent. After a large number of experiments, it is found that the transportation of foam concrete should be one-way, low-pulse, and uniform and constant flow. Among the conveying equipment hydraulic plunger pump, diaphragm pump, screw pump, hose pump and other pumps, only the latter two are close to the conveying requirements of foam concrete.

The biggest advantage of these two kinds of pumps is that there are no inlet and outlet valves, one-way pulse output, and no negative pulse caused by back-and-forth motion, which maximizes the protection of the original state of the product. Therefore, it is best to choose a hose pump for the transportation of foam concrete, because the pressure of the pump can reach 2.5MPa, which is twice that of the screw pump. It is the preferred equipment within the range of the maximum effective height specified in the current foam concrete industry standard.

3. Foam concrete wall formwork

Formwork-free foam concrete wall pouring is a composite composite of lightweight concrete slab, cement pressure slab, fiber cement slab, cement wood wool slab, calcium silicate slab and glass magnesium slab as permanent formwork and cast-in-place foam concrete. Insulated walls.

The formwork of the composite thermal insulation wall is a combination of the wall, and there is no formwork removal procedure, which makes the construction process more simplified, the work efficiency is higher, the construction period is shorter, and the shrinkage cracks of the foam concrete are effectively controlled. Composite thermal insulation wall is a new type of self-insulating wall, which is an integrated product of wall, thermal insulation and decoration.

TRUNNANO is a concrete additives supplier with over 12 years experience in nano-building energy conservation and nanotechnology development. We accept payment via Credit Card, T/T, West Union and Paypal. Trunnano will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.

If you are looking for high quality concrete additives, please feel free to contact us and send an inquiry:sales@cabr-concrete.com.

China's non-manufacturing purchasing managers index for March was released by the China Federation of Logistics and Purchasing and the Service Industry Survey Center of the National Bureau of Statistics today. An index of business activity for the non-manufacturing sector as a whole fell below 50 percent in March.

In March, China's non-manufacturing business activity index was 48.4%, down 3.2 percentage points from the previous month. The new orders index was 45.7 percent, down 1.9 percentage points from the previous month, indicating a significant slowdown in the growth of supply and demand in the non-manufacturing sector from the previous month.  In terms of sectors, the business activity index and new order index of transportation, accommodation and catering, culture, sports and entertainment, and tourism-related industries all declined significantly from the previous month.

Then the Foam concrete of the market may be affected by significant changes, the price will also be volatile, if you want to know the latest news of the Foam concrete, welcome to contact us.

Inquery us

Our Latest Products

Global early strength agent,superplasticizer for concrete market trend 2022-2028 Difference analysis between early strength agent and superplasticizer for concrete by Newswallpapers10

Early strength admixture refers to the admixture that can improve the early strength of concrete and has no significant effect on the later strength.Superplasticizer for concreter is a concrete admixture that can reduce the amount of mixing water whi…

Global 3D Printing Metal Powder market trend 2025-2027 What is the 3D Printing Metal Powder by Newswallpapers10

The oxidation resistance and corrosion resistance of nickel alloy make it suitable for the harsh environment of high temperature and high pressure.…

Global Graphite Lubricant market trend 2023-2030 What Is Graphite Lubricant? by Newswallpapers10

There are many types of lubricants available, from motor oils to special lubricants such as lithium-based lubricants.…